YAPSER 1001
Ceramic & Tile Adhesive
YAPSER 1001
Yapser 1001
Yapser 1001
Ceramic & Tile Adhesive
Description:
This is a cement-based ceramic and tile bonding mortar with
reduced slipping properties.
Areas of Usage:
It is used to bond small and medium sized materials such as tiles
and ceramics to be used in lateral and vertical surfaces plastered
with lean concrete, ferro-concrete, screed or cement.
Product Advantages:
Easy to apply
Does not slip.
Its adherence is high.
Technical specifications:
Slip: � 0.5 mm
Adhesion Strength:
-After Open Time: � 0.5 N / mm2 After at least 20 min
-Initial: � 0.5 N / mm2
-After Immersion in Water: � 0.5 N / mm2
-After Heat Exposure: � 0.5 N / mm2
-After Freeze-Thaw Cycle: 0.5 N / mm2
Temperature Resistance: (-30 ° C) – (+70 ° C)
Reaction to Fire Class: A1
*The above values are valid for 28 days of performance, which were
obtained through laboratory tests.
Application Information:
Application Temperature: (+5 ° C) – (+35 ° C)
Mixing Ratio: 6 – 7 lt water / 25 kg powder
Pot life: 2 hours
Open time: 20 min.
Application thickness: 3-10 mm
Grouting Time: 24 hours
Average Consumption: 3 – 5 kg / m2
These values are valid for 23 ° C and 50% relative humidity. Times
may vary depending on ambient conditions.
Surface Preparation:
The application surface should be made clean from dust, dirt,
oil, paint residue, and other similar adherence reducing foreign
materials.
Care must be taken to ensure that the application surface is set.
The surface must be moistened before application.
The dusty surface behind the ceramic should be moistened and
wiped
Mixture Preparation:
25 kg Yapser 1001 should be added slowly to 6-7 liters of water. The
mixture then should be blended with a trowel or a low-speed mixer
in a way that no loccules remain, until a homogeneous mixture is
obtained. The homogeneously mixed mortar should be rested for 5
minutes and then mixed again to make it ready for application.
The prepared mixture should be used within a maximum of 2 hours
and mixtures that are waiting to be used during this period should be
mixed intermittently. Any mortar which has started to harden or has
expired should not be used.
Application:
The prepared mixture should be spread on the surface with the lat
part of the trowel to ensure good adhesion and then combed with a
toothed trowel suitable for size of the tile to be used. Ceramics must
be bonded to the combed mortar within 20 minutes. Good adhesion
should be provided by pressing on the laid material by hand and
applying force with rubber hammer.
Adhesive should be used by applying it to small areas and any
adhesives whose material bonding was delayed and has started to
cake should be scraped clean from the surface.
The excess adhesive in the joint gaps should be scraped before
drying, and the mortars smeared on the surface should be cleaned
with a damp cloth.
Applications should not be carried out in temperatures below -5°C.
Without taking protective measures, applications should not be
made on surfaces that are exposed directly to sun and wind.
Foreign materials should never be mixed into the mortar.
All tools used should be washed after application with water before
drying.
-The grouting process can be started after 24 hours.
Tiles bonded with Yapser 1001 should not be exposed to water for at
least 24 hours.
Depending on the application area and the type of ceramic to be
applied, double-sided bonding should be used.
Caution:
Do not breathe the product directly, as it is cement-based. Avoid
contact with skin and eyes.
Reference Standard:
TS EN 12004 -1 / C1T Class
C: Cement-based
1: Standard performance
T: Reduced slipping
Colors: Gray
Package: 25 kg. kraft paper bag
Shelflife: 12 months in dry environment and in original packaging